moog-es800030 | Front Outer Tie Rod End | Chevrolet Cobalt | ES800030

  • moog-es800030 360image 1
  • moog-es800030 Front Outer Tie Rod End
  • moog-es800030 Front Outer Tie Rod End
  • moog-es800030 Front Outer Tie Rod End
  • moog-es800030 Front Outer Tie Rod End
  • moog-es800030 360image large 1

Front Outer Tie Rod End

Manufacturer: MOOG
Part Number: moog-es800030
Price: $35.88

check_box In Stock check_box Ships Immediately


  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.

    WARRANTY:

    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

    Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)

question_answer Ask us a Question

FitmentFront Outer Tie Rod End moog-es800030 fits these vehicles:

moog-es800030 | Front Outer Tie Rod End | Chevrolet Cobalt | ES800030

Moog Tie Rods

Connecting the Driver to the Vehicle

Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.

Moog Tie Rod Box
Moog Tie Rod

Designed for Strength, Durability, and Longevity

Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.

Fitment for moog-es800030
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
ChevroletCobalt2010-2005Outer Quantity 2
ChevroletEquinox2009-2005Outer Quantity 2
ChevroletHHR2011-2006Outer Quantity 2
PontiacG52010-2007Outer Quantity 2
PontiacPursuit2006-2005Outer Quantity 2
PontiacTorrent2009-2006Outer Quantity 2
SaturnIon2007-2003Outer Quantity 2
SaturnVue2009-2002Outer Quantity 2

question_answer Customer Questions and Answers


Question:
are the tie rod ends side specific can they be installed on either (side driver of passenger side)
Answer:
Yes, they can be installed on either side for the front outer!

Question:
Do the outer tie rod ends come pre greased and if they do is there a specific grease that is recommended and compatible with the grease it came with.
Answer:
After moog-es800030 is assembled it is greased. This is to preserve the tie rod while it sits on the shelf. After it is installed it needs to be greased and every oil change. Use a grease that has the NLGI rating. The grease Moog uses is compatible w with any grease. ...see more

Question:
What size castle nut is used on the ES800030 tie rod end?
Answer:
The castle nut would be m12x1.75 on the ES800030 tie rod.

Question:
Is this one (1) tie rod end, or a pair (2) ?
Answer:
All Moog sway bar end links are sold individually. Not in pairs.