moog-es415rl | Front Outer Tie Rod End | 71-72 Chevrolet Blazer | MOOG

  • moog-es415rl 360image 1
  • moog-es415rl Front Outer Tie Rod End
  • moog-es415rl Front Outer Tie Rod End
  • moog-es415rl Front Outer Tie Rod End
  • moog-es415rl Front Outer Tie Rod End
  • moog-es415rl 360image large 1

Front Outer Tie Rod End

Manufacturer: MOOG
Part Number: moog-es415rl
Price: $36.54

check_box In Stock check_box Ships Immediately

  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.


    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

FitmentFront Outer Tie Rod End moog-es415rl fits these vehicles:

moog-es415rl | Front Outer Tie Rod End | 71-72 Chevrolet Blazer | MOOG

Fits Left or Right Side

Moog Tie Rods

Connecting the Driver to the Vehicle

Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.

Moog Tie Rod Box
Moog Tie Rod

Designed for Strength, Durability, and Longevity

Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.

Fitment for moog-es415rl
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
ChevroletBlazer1972-1971OuterRWD Quantity 2
ChevroletC10 Pickup1972-1971Outer Quantity 2
ChevroletC10 Suburban1972-1971Outer Quantity 2
ChevroletG10 Van1972-1971Outer Quantity 2
ChevroletP10 Van1972-1971Outer Quantity 2
GMCC15/C1500 Pickup1972-1971Outer Quantity 2
GMCC15/C1500 Suburban1972-1971Outer Quantity 2
GMCG15/G1500 Van1972-1971Outer Quantity 2
GMCJimmy1972-1971OuterRWD Quantity 2
GMCP15/P1500 Van1972-1971Outer Quantity 2

question_answer Customer Questions and Answers

What are the dimensions on the ES415rl?
Stud center to end: 6.385 Rod Thread: 11/16 - 18RH Configuration: Straight Rod Type: Male Stud Diameter Dimension: (top in) 0.507 Stud Diameter Dimension: (bottom in) 0.625 Stud Thread: 1/2 20