lock Warranty Information keyboard_arrow_down
Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.
WARRANTY:
Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.
Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.
If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.
Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)
moog-es3475 | Front Inner Tie Rod End | Jeep Grand Cherokee 1999-2004
Moog Tie Rods
Connecting the Driver to the Vehicle
Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.
Designed for Strength, Durability, and Longevity
Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.
Product Reviews for moog-es3475 | Front Inner Tie Rod End | Jeep Grand Cherokee 1999-2004
- 5 Star (3)
-
-
- 100%
-
- 4 Star (0)
-
-
- 0%
-
- 3 Star (0)
-
-
- 0%
-
- 2 Star (0)
-
-
- 0%
-
- 1 Star (0)
-
-
- 0%
-
MOOG moog-es3475
starstarstarstarstar" Good "
Good.
verified_user Verified Buyer - Ryan Welter - . MOOG moog-es3475 - 5 out of 5starstarstarstarstar" Wonderful "
Dont buy stock parts, everything I get from Moog has out performed the rest.
verified_user Verified Buyer - sam schmitz - . MOOG moog-es3475 - 5 out of 5starstarstarstarstar" Better than oem "
Moog came recommended by other off-roaders. Appears to have quality design and construction. Much beefier than OEM with a nice finished look. Zerk fittings are great, the stock part was not greasable and had no zerk.
verified_user Verified Buyer - Stephen Perkins - . MOOG moog-es3475 - 5 out of 5question_answer Customer Questions and Answers
- Question:
- Do I need to grease part number es3475 before installation? If yes, how much grease do I apply and how often do I need to re-grease it?
- Answer:
- Yes, it is very important to grease the tie rod before after installation. Pump grease in until the boot starts to expand and stop. Moog recommends you grease at every oil change. One to two pumps after the first time greasing should be good.