moog-ds1289 | Front Left Inner Tie Rod | Ford E-250 | MOOG-DS1289

  • moog-ds1289 Front Inner Tie Rod End - Driver Side
  • moog-ds1289 Front Inner Tie Rod End - Driver Side

Front Inner Tie Rod End - Driver Side

Manufacturer: MOOG
Part Number: moog-ds1289
Price: $77.72

check_box In Stock check_box Ships Immediately


  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.

    WARRANTY:

    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

    Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)

question_answer Ask us a Question

FitmentFront Inner Tie Rod End - Driver Side moog-ds1289 fits these vehicles:
Details

moog-ds1289 | Front Left Inner Tie Rod | Ford E-250 | MOOG-DS1289

Fits Driver Side Only. Inner at Connecting Tie Rod End

Moog Tie Rods

Connecting the Driver to the Vehicle

Tie rods are a crucial part of your steering system. When you turn your steering wheel the motion travels through the steering rack, through the tie rods, and finally through your steering arm or spindle. Without tie rods, you wouldn't be able to turn your car. This part is also incredibly important to your vehicle's alignment. If you replace your tie rods, make sure to get an alignment done immediately afterward.

Moog Tie Rod Box
Moog Tie Rod

Designed for Strength, Durability, and Longevity

Moog tie rods feature several differences from the OE. One of the more obvious differences is the overall design itself. Whereas many OE tie rods are two-piece assemblies, Moog's tie rods are forged one-piece units. This one-piece design reduces the chance of early wear, increasing the durability of the part as a whole. To protect your tie rod, Moog uses a neoprene-sealed rubber dust boot. This dust boot is resistant to both extreme temperatures and abrasion. The design for this rubber boot includes a small valve to allow for the flushing of old grease and contaminants. In addition to all these other features, Moog crafts their tie rod end using hardened full-ball metal studs. These hardened studs can stand up to much more than the OE, making the tie rod that much more dependable.

Fitment for moog-ds1289
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
FordE-2502006-2003Left Inner Quantity 1
FordE-250 Econoline2002-1992Left Inner Quantity 1
FordE-350 Club Wagon2005-2003Left Inner Quantity 1
FordE-350 Econoline1998-1992Left Inner Quantity 1
FordE-350 Econoline Club Wagon2002-1992Left Inner Quantity 1
FordE-350 Super Duty2006-1999Left Inner Quantity 1

question_answer Customer Questions and Answers


Question:
What is the rod and rack end thread on part number ds1289?
Answer:
On part number ds1289, the rod thread is M22 x 1.50 and the rack end thread is M14 x 1.50.

Question:
What is the length of part number ds1289?
Answer:
The length of part number ds1289 is 17.80 inches. From the center of the tapered stud to the end of the threads.